Here it goes...

take off the trim pieces and removs the old Bose
[IMG]local://upfiles/6540/EF3B1D86AE014035B2E9A9C78E141250.jpg[/IMG]
remove the fuse trim and the passenger side vents

[IMG]local://upfiles/6540/3CBE41C6FB7F41A7A666EB0CB63667DC.jpg[/IMG]

[IMG]local://upfiles/6540/2C41831139D348A48964DCB051163BC3.jpg[/IMG]

remove the bottom trim and locate the Bose reciever box
[IMG]local://upfiles/6540/A6C1E8C6A86740B7BFEBDC93C3E4BEB6.jpg[/IMG]

[IMG]local://upfiles/6540/FAE1E3BFD6A14F5D9CB6862DA6D94090.jpg[/IMG]

 

next...pull the three plugs from the Bose reciever

[IMG]local://upfiles/6540/5DA78319085E4A14841D0440F6CC6E00.jpg[/IMG]

plug these three little jewels into the wire harness
[IMG]local://upfiles/6540/CB6F8C6F224349D8B1AEFF2067388642.jpg[/IMG]


[IMG]local://upfiles/6540/3F7D014B652D46D6B1D1F9C13B7C95CA.jpg[/IMG]

start cutting and labeling wires to extend the wire harness. I used about 4ft. MAKE SURE YOU LABEL THE WIRESCORRECTLY BEFORE YOU PULL

[IMG]local://upfiles/6540/53B2ADA738F24D73B227662F5F2C4760.jpg[/IMG]

 

Then...Pull the wires through to the stereo "hole" and to the new wire harness

[IMG]local://upfiles/6540/17BB1903E1D54A888CF428B4A2E50699.jpg[/IMG]

[IMG]local://upfiles/6540/22965F3087534441AA329EF5F7803270.jpg[/IMG]

Connect your labeled wires. Make sure connections are tight andsealed.
[IMG]local://upfiles/6540/E31D41F6C7D14715B9D5A91F5EC8EAFA.jpg[/IMG]

Next connect the ends of the stereo harness to your pulled wires. Make sure they are secure.
[IMG]local://upfiles/6540/F60C87F9B92A40AF9262DD4D2AECBC17.jpg[/IMG]

 

after that... I worked on the mounting bracket...

[IMG]local://upfiles/6540/41D4E0A3D9D748B09C320D3F52BBCA43.jpg[/IMG]

Severe "MACGUYVERING"was necessary to make all things fit just right. You will see what I mean when you try. Here are some of the things that I did. They worked for me. Feel free to make improvements as you see fit.
[IMG]local://upfiles/6540/B04C4493213F45D3B7BC3C5A3538765F.jpg[/IMG]
A little cardboard to fill the gap and add support since only one mounting bracket screw hole lined up right.

[IMG]local://upfiles/6540/5AFC4815BAEE4448A018A06044FB03BF.jpg[/IMG]

I used some styrofoam to make "pillars". This was cut from the styrofoam padding the new reciever in the box. I used two pieces on the left side to hold up the bracket and shelf where there was no screw to mount to... you'll see.
[IMG]local://upfiles/6540/248F6333CF564F9083DB25E7866DF79E.jpg[/IMG]

 

Finally...[sm=bling.gif][sm=Flahssssss.gif][sm=happybounce.gif][sm=hail.gif][sm=happy046.gif][sm=signs003.gif][sm=wootwoot.gif]Thanks to all those that posted info previously about this topic. I hope that this can help a lot of people in the future. Please feel free to comment on this. THANKS CORVETTEFORUMS.COM

[IMG]local://upfiles/6540/942371BF7F8F4DF48817DA619890D8BB.jpg[/IMG]

[IMG]local://upfiles/6540/210344633EF44AFB8478FF971D185839.jpg[/IMG]

 

Great job! enjoy your new tunes. Cheers

 

Looks good!

 

has anybody put a in-dash tv in their c4 im thinking about it any input would be nice any pic would be nicer

 

Great job and great pictures, I'm sure that will help out the next person, PG.